Archives

Features at a glance:
– 4U/84 HP CompactPCI 2.16 system platform with rear I/O, for horizontal installation of 6U cards
– Card rack acc. to IEEE 1101.1, 1101.10 / 11 and IEC 60297-3-101, -102, -103
– CompactPCI 2.16 backplane to hold up to 4 CompactPCI power supply units (P47 connectors)
– Cooled by 7 fans (air flow from left to right)
– Completely assembled and wired

– CompactPCI card rack, painted black outside (RAL9005), screened, with IEEE card guides and ESD clip mounted on the right side
– CompactPCI 2.16 PSB backplane, 6+3 U, 8 slot, 64-bit/33 MHz, system slot left, V (I/O)=3.3V, with rear I/O, with 3 P47 connectors, acc. to PICMG 2.16 R. 1.0
– 2x 250W CompactPCI power supply units with wide range input 90 – 264 VAC, 250 W, (3,3 V / 33 A, 5 V / 33 A, 12 V / 5,5 A, -12 V / 1 A) with PFC, with P47 connector, incl. 3 U / 8 HP front panel
– Power supply connector with switch, fuse and filter
– Partial front panel 32 HP / 3 U with cutout for power supply connector, EMC spring
– 6x DC fan, 80 x 80 x 25, 36.4CFMfan/29db(A)
– 2x Blanking plate 8 HP/3 U with EMC spring

Dimensions
W: 482.6 mm
H: 175.9 mm
D: 280.6 mm

Order number:
LMH0000140

– Measurement and testing of CompactPCI assemblies in the 3U or 6U Eurocard format is greatly facilitated by the use of these test adapters
– Optimal access to the test boards is guaranteed because the adapter has plug-in connection on 3 sides
– Test boards are securely held by the front and lateral guides
– The modern BRIDGE design permits up to 3 CompactPCI cards and one standard PCI card to be inserted in one CompactPCI slot
– This allows system developers to implement a large number of tests with little effort while having access to the large number of PCI boards available worldwide
– Test adapter can be easily used even in systems with longer CPCI cards (up to 220 mm)
– Complete Windows support provided by this product facilitates fast system integration
– Additional drivers are not needed
– PCI devices are detected by a standard PCI BIOS with BIOS extension
– Controlled impedance layout design guarantees optimal reliability

– Further advantages of the adapters are:
– 32-bit bridge with INTEL 21152 (33 MHz), 3U
– 64-bit bridge with INTEL 21154AC (33MHz), 6U
– 4HP (.8″) installation width, 3U/6U
– Full plug-and-play support
– Automatic voltage adaptation to 3.3V/5V backplane V(I/O)
– Secondary V(I/O) adjustable by means of jumper
– Supply voltage for bridge operation of 5V (single) from backplane
– LED indicators for all secondary voltages
– All operating voltages can be separated for current consumption measurement
– Simple adaptation to different interrupt tables by means of jumpers
– JTAG support
– Geographic addresses can be individually set for each slot, 6U
– All 315 I/O signals can be individually seperated with jumpers, 6U
– High-resistance switching of PCI bus signals via the bridge
– EMC-compliant design
– 8 GND test points facilitate measurement on the test bards
– Guided insertion of test boards from 3 sides
– Specifications, PCI V2.1, PICMG 2.0 R2.1 and R3.0

Order numbers:
3610000600, 3U
3660000100, 6U

– The cPCI load board serves to simulate loads on cPCI back wall wiring systems or racks
– Both electrical and thermal conditions can be simulated
– The following load streams can be switched with the coding and tilt lever switches located on the front plate:

Control Options
5 V in .55A stages
3.3 V in .7A stages
+12 V off/1A
-12 V off/1A

– 5V must always be connected as control voltage
– Voltages are tapped at the cPCI bus via the P1 plug

Excessive temperature protection:
– Load test card switches itself off at a temperature on the top side of the load test card or in the rack of 120 degrees C +-5 K

– Incoming voltage levels for the voltages 5V, +12V, 3.3V, -12V can be measured at measuring points close to the plug P1
– These measuring points are run via the plug X1 (on the front plate)
– 4 PTC resistors (PT100) are attached to the load card: On the front at bottom and top and on the back at the bottom and top
– It is possible to measure the temperature on the load test card or in the rack via these
– The PTC resistor connections are also run via the plug X1

Order number:
LXH0000630 (HE2675 Rev 00)